Anniversary Special Edition Eachine Minicube Flytower 20x20mm Compatible Frsky Flysky DSM RX F3 ESC

Wish3

$111.99 $132.99

Sorry, this item is out of stock

Anniversary Special Edition Eachine Minicube Flytower 20x20mm Compatible Frsky Flysky DSM RX F3 ESC
 


















 
Description:
Brand name: Eachine
Mount hole: 20mm*20mm
Size: 27mm*27mm*20mm
Weight: 9.4g

1. Eachine Minicube Receiver 
1). Eachine Minicube DSM2/ DSMX satellite Receiver 
Frequency range: 2.403-2.479Ghz
Input power: 5V
Response time: 22ms / 11MS
Resolution: 2048
Display method: LED
Operating voltage: 3.3V
Working current: 60MA
Size: 27mm*27mm*7mm
Mount hole:20mm*20mm
Weight: 3.1 g
Antenna length: 100mm 
Data format: Serial port
Protoco: DSM2/DSMX
Distance: no ground interference (1 m from the ground ) > 300m
Uses: indoor small aircraft.
Compatible Transmitters: DSM2 / DSMX series of remote control
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
 
2). Eachine Minicube Flysky 8CH AFHDS2A receiver
Channels: 8CH
Model type: Multi-rotor
Frequency range: 2.408-2.475GHz
2.4GHz system: AFHDS 2A
Transfer method: FHSS
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >300m
Working current: 40mA
Size: 27*27*7mm
Mount hole:20mm*20mm
Weight: 3.1g
Ibus output with failsafe
Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F
 
3).  Eachine Minicube Frsky  Compatible  2.4G 8CH Receiver:
Frequency range: 2.403-2.479Ghz
Channels: 8CH 
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST 
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)
 
2. Eachine Minicube F3 V1.1 6DOF Flight Controller:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Working voltage: 2-3S Lipo
Processor: STM32 F303 MCU
Sensor: SPI Sensor MPU6000
Built-in Betaflight OSD (Batt voltage, RSSI, Fly mode, Flytime, Craft name etz.)
Firmware version: Betaflight 3.1 Dshot ready
Target: OmnibusF3
This V1.1 version comes with SH1.0 plug instead of USB interface, intergrated filtration module.
 
3. Eachine Minicube 10A BLHeli_S 4 In 1 ESC:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 2-3S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on
 
Features:
STM32 F303MCU + BLHELI_S ESC make your Operating feel more stabilly and silky
Jaw-dropping flight performance
LED_STRIP solder pin
BUZZER Ready
Betaflight support
Acro mode / Air mode /Angle mode support 
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
OSD Configuration has been include in BETAFLIGHT GUI
Radio Stick to control PID Tunes
 
Package included:
1 x Minicube Receiver 
1 x Minicube F3 V1.1 6DOF Flight Controller
1 x Minicube 10A BLHeli_S 4 In 1 ESC