Fpv Racing Rc Drone F4 Osd 30a Blheli_s 40ch - Tyro99 210mm

Eachine Tyro99 210mm DIY Version FPV Racing RC Drone w/ F4 OSD 30A BLHeli_S 700TVL Camera 5.8G 40CH 600mW VTX

Specifications:

• This is the DIY version that comes unassembled.
• Make sure the antenna is installed at the output end before powering up to avoid damaging internal components
• Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components
• If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance
• Pay attention to classic protection during transportation and installation.
• Take-off weight is about 450g.
• Wheelbase: 210mm
• Frame arm thickness: 5mm
• Bottom plate thickness: 2mm
• Side plate thickness: 2mm
• Frame kit material: 3K carbon fibre & 6065 aluminium
• Motor KV: 2150RPM/V
• Idle current (Io/10V): 1.26A
• Lipo cell: 3-5S
• Weight: 31g
• Max continuous current: 31A
• Max continuous power: 496W
• Max thrust: 1050g (4S/5")
• Configuration: 12N/14P
• Motor Resistance (RM): 0.0572 Ω
• Stator Diameter: 22mm
• Stator Thickness: 6mm
• Motor diameter: 27.7mm
• Motor body length: 19.2mm
• Overall shaft length: 34.2mm
• Prop adapter shaft: M5
• Bolt holes spacing: 16mm
• Bolt thread: M3
• Propeller: 5-6 inch
• Continuous current: 30A
• Burst Current: 40A(10S)
• Input voltage: 2-5S
• BEC: 5V 2A BEC
• Main control chip: 48Mhz EFM8BB2
• Firmware: BLHeli_S supports Dshot600
• MOS: 5*6
• Main control chip: STM32F405
• Sensor: ICM20602
• Power supply: 5V
• Integrated OSD
• Onboard LC filter
• PID cycle rate & gyroscope refresh rate up to 32Khz
• Supports BetaFlight / inav racing firmware
• 700TVL CMOS Camera
• Case size: 25mm*25mm
• Weight: 9.5g
• Total pixels: PAL: 1020H×596V (0.61MP) NTSC: 1020H×508V (0.52MP)
• Effective pixels: PAL: 976H×582V (0.57MP) NTSC: 976H×494V (0.48MP)
• Signal system: NTSC
• Resolution ratio(horizontal center): 700TVL
• Video output: 1.0Vp-p/75Ω
• Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
• White balance: on/off optional
• Exposure mode: electron exposure
• Electronic shutter: 1/50(1/60) 1/100000 S
• Gamma correction: 0.45/1.0
• Synchronization method: inter-sync
• Camera lens: standard 2.8mm
• Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V)
• Working current: 70mA (low power consumption)
• Working temperature:20℃~-60℃
• Humidity: 0%~98%
• 8G 40CH 0mW/25mw/200mw/600mw switchable VTXOutput power & transmission distance: ≥[email protected], ≥[email protected], ≥[email protected]
• Transmitting power: 0mW/25mW/200mW/600mW
• Full video format: NTSC /PAL
• Input voltage & power dissipation: 7V~24V, +12V/[email protected]
• Size: 20*30*9mm
• Weight: ≤7g(except antenna)
• With output power self-check function.
• Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
• Racerstar 5040 2 Blade Propeller
• Material: PC
• Mounting hole: 5mm
• Quantity: 2 CW & 2 CCW
• Colour: blue, red, yellow, purple, white (Delivery colour randomly
• Battery Not included
• Recommend 3-5S

Package included:

• 1 x 210mm frame kit
• 2 x2206 2150KV brushless motor CW
• 2 x2206 2150KV brushless Motor CCW
• 1 x4 IN 1 30A BLHeli_S ESCSpecifications:
• 1 xCustomized F4 flight controller
• 1 x700TVL CMOS camera
• 1 x5.8G 40CH 0mw/25mw/200mw/600mw switchable VTX
• 2 x Battery strap
• 2 x Racerstar 5038 2 blade propeller CW
• 2 xRacerstar 5038 2 blade propeller CCW